Units regularly using crane lifts repair and maintenance, and develop a regular monitoring system, including daily monitoring, weekly inspection, monthly inspection, annual inspection, dynamic control of the crane, there are always exceptions to that time had been found in order protect the safe operation of cranes. How to Choose Right tory burch shoe in for December Operation of the driver is responsible for routine maintenance projects, especially clean, transmission parts, adjustments shortening and tightening of the job. What is the Future of Luxurious tory burch outlets ? God Knows! Sensitivity of the investigation by the reliability of safety devices, control of abnormal operation of the audio. Jointly carried out the maintenance workers and managers, the daily inspection items, the main contents of the visual inspection, check out the hook, the extract tool, rope and other uses of public safety, brakes, clutch, emergency alarm system device sensitivity, reliability, run to the observed abnormal noise transmission components, and overheating.Crane mismanagement, the driver or control officers are not strict examination system, the equipment "sick", and there is no strict rules, properly maintained, will be increased to crane failure; used improperly, such as overloading, crane oblique suspension will cause damage Dengjun ; poor maintenance, such as oil spills, oil is not enough, electrical aging, will result in crane is not working properly. Crane maintenance work in order to establish normal maintenance, improve maintenance quality, reduce maintenance downtime when Taiwan is an important work, especially repair of equipment is more important. Equipment in the maintenance process, to reduce maintenance as much as possible the number of days rest, but also to ensure the required maintenance of equipment after the technical conditions, we must take the process of repair and maintenance before the technical preparations to do. Crane repair process from start to finish are technical demanding job.Prominent tory burch reva on sale are One of Most Fitting Vogue in November

Demolition inspection hook, shaft, beams, pulleys, bearings and clean lubrication, hooks, beams, pulleys, shafts, are not allowed to have cracks, some should not be loose thread, bearing in good condition, turn the pulley, screw groove at the back there are knife marks or cracks should be replaced. Check the wear of dangerous sections, dangerous section of wear more than 10% of its original height should be replaced. Hook test, overhaul, the hook should be a test checks to 1.25 times the rated load suspended for 10 minutes, hook elastic mouth open mouth hook size should not exceed 0.25%, there should not be permanent deformation after unloading and crack; board hook maintenance, riveting hook after the board, board and the board of the gap, should not be greater than 0.3mm.How to Find Your Perfect tory burch flats sale

Check the broken wire: a twist away from the broken wire within the wire more than 10% of the total number of standards should be scrapped; radial wear: wire diameter of radial wear more than 40% of the original, the whole root of rope should be scrapped; deformation check: wire rope diameter shrink the volume to 70% of rope diameter kink, rope core at the exposed, Breaking new ones should be discarded wire rope; wire rope lubrication: lubrication with a wire brush before, such as kerosene, cleaning, linen with a wire rope or synthetic graphite grease lubrication that calcium-based dipping saturation is appropriate; crane pulley repair: repair washable pulley, check crack, pulley shaft shall be no crack, no wear and tear of the original diameter of journal 30%, cone of not more than 5%, more than the value that should be replaced; pulley groove maintenance, check the pulley groove with the model, radial wear should not exceed 30% of wall thickness, or should be scrapped. Shall not exceed the standard may repair, overhaul, after checking with the model, the bottom and lateral clearance should not be greater than 0.5mm, and the pulley wheel groove center line deviation of the center line should not exceed 0.2mm, center groove profile end of the deviation should not exceed 1mm; shaft hole inspection, overhaul, the axle hole to allow not more than 0.25CM2 defects, the depth should not exceed 4mm; assembly, assembly, should be able to hand a flexible rotation, lateral oscillation may not More than D/1000. The name of D-pulley diameter; crane reel maintenance; drum groove, groove wear and tear than 2mm should be re-car system, overhauled the drawing requirements to be met groove, but the drum wall thickness of not less than 81% of the original thickness ; roll surface, roll the surface should not have crack, should not have significant loss of roundness, plate screws should not be loose; roll axis, roll axis not have the crack, after the overhaul should meet requirements of the drawings, wear more than 5% of nominal diameter, should be replaced with new parts; assembly and installation of a small frame drum shaft centerline and the bearing surface to be parallel, the deviation should not be large 1mm / m, after the installation of two shaft ends of the center line of reel should be no deviation greater than 0.15mmThe New Tory Burch Flats for Summer

Tags: Tory Burch Online

Bookmark: